A new disk was presented to a server as /dev/ sdd. The systems administrator needs to check if a partition table is on that disk. Which of the following commands can show this information?
Correct Answer:
B
The command that can be used to check if a partition table is on a disk is fdisk. The fdisk command can display, create, delete, and modify partitions on a disk. To show the partition table of a disk, the administrator can use fdisk -l /dev/sdd (B). References:
✑ [CompTIA Linux+ Study Guide], Chapter 5: Managing Filesystems and Logical Volumes, Section: Partitioning Disks
✑ [How to Use Fdisk Command in Linux]
A Linux engineer receives reports that files created within a certain group are being modified by users who are not group members. The engineer wants to reconfigure the server so that only file owners and group members can modify new files by default. Which of the following commands would accomplish this task?
Correct Answer:
B
The command umask 002 will accomplish the task of reconfiguring the server so that only file owners and group members can modify new files by default.
The umask command is a tool for setting the default permissions for new files and directories on Linux systems. The umask value is a four-digit octal number that represents the permissions that are subtracted from the default permissions. The default permissions for files are 666, which means read and write for owner, group, and others. The default permissions for directories are 777, which means read, write, and execute for owner, group, and others. The umask value consists of four digits: the first digit is for special permissions, such as setuid, setgid, and sticky bit; the second digit is for the owner permissions; the third digit is for the group permissions; and the fourth digit is for the others permissions. The umask value can be calculated by subtracting the desired permissions from the default permissions. For example, if the desired permissions for files are 664, which means read and write for owner and group, and read for others, then the umask value is 002, which is 666 - 664. The command umask 002 will set the umask value to 002, which will ensure that only file owners and group members can modify new files by default. This is the correct command to use to accomplish the task. The other options are incorrect because they either do not set the default permissions for new files (chmod 775 or chown - cf) or do not exist (chattr -Rv). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 11: Managing File Permissions and Ownership, page 349.
A systems administrator needs to clone the partition /dev/sdc1 to /dev/sdd1. Which of the following commands will accomplish this task?
Correct Answer:
C
The command dd if=/dev/sdc1 of=/dev/sdd1 copies the data from the input file (if) /dev/sdc1 to the output file (of) /dev/sdd1, byte by byte. This is the correct way to clone a partition. The other options are incorrect because they either compress the data (tar -cvzf), synchronize the files (rsync), or copy the files over a network (scp), which are not the same as cloning a partition. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 10: Managing Storage, page 321.
A Linux administrator is troubleshooting an issue in which an application service failed to start on a Linux server. The administrator runs a few commands and gets the following outputs:
Based on the above outputs, which of the following is the MOST likely action the administrator should take to resolve this issue?
Correct Answer:
B
The administrator should increase the TimeoutStartUSec configuration for the logsearch.service to resolve the issue. The output of systemct1 status logsearch.service shows that the service failed to start due to a timeout. The output of cat /etc/systemd/system/logsearch.service shows that the service has a TimeoutStartUSec configuration of 10 seconds, which might be too short for the service to start. The administrator should increase this value to a higher number, such as 30 seconds or 1 minute, and then restart the service. The other options are incorrect because they are not related to the issue. The service is already enabled, as shown by the output of systemct1 is-enabled logsearch.service. The service does not use an OnCalendar configuration, as it is not a timer unit. The service does not use a KillSignal configuration, as it is not being killed by a signal. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 14: Managing Processes and Scheduling Tasks, pages 434-435.
A systems administrator wants to delete app . conf from a Git repository. Which of the following commands will delete the file?
Correct Answer:
D
To delete a file from a Git repository, the administrator can use the command git rm app.conf (D). This will remove the file “app.conf” from the working directory and stage it for deletion from the repository. The administrator can then commit the change with git commit -m "Delete app.conf" to finalize the deletion. The other commands will not delete the file, but either tag, commit, or checkout the file. References:
✑ [CompTIA Linux+ Study Guide], Chapter 10: Working with Git, Section: Deleting Files with Git
✑ [How to Delete Files from Git]